#Accu chek 360 software free download update#
#Accu chek 360 software free download android#
#Accu chek 360 software free download Bluetooth#

Configure the pump using 360 config software.Detecting a new TBR on the pump might take up to 20 minutes and the TBRвЂ™s effect will only be accounted from the moment it is detected, so in the worst case there might be 20 minutes of a TBR that is not reflected in IOB. Setting a TBR on the pump is to be avoided since the loop assumes control of TBRs.(-> DonвЂ™t bolus from the Pump! See chapter Usage below) Boluses on the pump are always checked before a high TBR or a bolus issued by AAPS but due to the limitations AAPS will then refuse to issue the TBR/Bolus as it was calculated under false premises.Issuing a bolus from the pump will not always be detected in time (checked for whenever AAPS connects to the pump), and might take up to 20 minutes in the worst case.So if you see those errors frequently your only option at this time is to get another phone thatвЂ™s known to work well with AndroidAPS and the Combo (see above). There is very little that can be done to remedy either of those issues at this point.There is another issue were a restart doesnвЂ™t help but a button on the pump must be pressed (which resets the pumpвЂ™s Bluetooth), before the pump accepts connections from the phone again.

#Accu chek 360 software free download Bluetooth#

If that error occurs, make sure Bluetooth is enabled, press the Refresh button in the Combo tab to see if this was caused by an intermitted issue and if still no connection is established, reboot the phone which should usually fix this.

Bluetooth connection stability varies with different phones, causing вЂњpump unreachableвЂќ alerts, where no connection to the pump is established anymore.

Occasionally (every couple of days or so) AAPS might fail to automatically cancel a TBR CANCELLED alert, which the user then needs to deal with (by pressing the refresh button in AAPS to transfer the warning to AAPS or confirming the alert on the pump).

This is because cancelling a TBR causes an alert on the pump which causes a lot of vibrations.

If the loop requests a running TBR to be cancelled the Combo will set a TBR of 90% or 110% for 15 minutes instead.

Similarly, when reducing to 50%, the lowest basal rate must be at least 0.10 U/h. when increasing to 200%, the highest basal rate must not exceed 5 U/h since it will be doubled. This also applies when modifying a profile, e.g.

Currently only basal rates in the range of 0.05 to 10 U/h are supported.

#Accu chek 360 software free download update#

ItвЂ™s currently not possible to set the time and date on the pump, so daylight saving time changes have to be performed manually (you may disable the phoneвЂ™s automatic clock update in the evening and change it back in the morning together with the pump clock to avoid an alarm during the night).Setting a basal profile other than 1 on the pump or delivering extended boluses or multiwave boluses from the pump interferes with TBRs and forces the loop into low-suspend only mode for 6 hours as the the loop canвЂ™t run safely under these conditions.Extended bolus and multiwave bolus are not supported (see Extended Carbs instead).

#Accu chek 360 software free download android#

This allows using phones with Android < 8.1 but has not been widely tested:

For advanced users, it is possible to perform the pairing on a rooted phone and transfer it to another rooted phone to use with ruffy/AAPS, which must also be rooted.

Be aware that while Android 8.1 allows communicating with the Combo, there are still issues with AAPS on 8.1.

You are encouraged to also enter your experience and thereby help others (these projects are all about paying it forward).

Please be aware that this is not complete list and reflects personal user experience.

A list of phones can be found in the AAPS Phones document.

With LineageOS 14.1 it has to be a recent version from at least June 2017 since the change needed to pair the Combo pump was only introduced at that time.

As of AndroidAPS 3.0 Android 9 is mandatory.

A compatible phone: An Android phone with a phone running LineageOS 14.1 (formerly CyanogenMod) or at least Android 8.1 (Oreo).

(Roche sends out Smartpix devices and the configuration software free of charge to their customers upon request.)

A Smartpix or Realtyme device together with the 360 Configuration Software to configure the pump.

A Roche Accu-Chek Combo (any firmware, they all work).

Useful resources to read before you start.

Frequent questions on Discord and their answers.

Time adjustment daylight savings time (DST).

Hints and Checks after update to AAPS 3.0.

What is a closed loop system with AndroidAPS.